A wakeboard tower is the aluminum or stainless arch over a towboat’s cockpit. It started as a way to raise the tow point for wakeboarders. Today it also carries board racks, lights, a bimini top and, usually, a set of speakers aimed back at the rider. This guide covers what a tower does, how to choose an aftermarket one for a boat that didn’t come with one, and what to look for in tower speakers.
What a wakeboard tower does
On a boat without a tower, the rope attaches to a low pylon or a ski eye near the transom, so the pull is nearly horizontal. Mount the rope on a tower several feet higher and the pull angles upward. That upward component helps a wakeboarder rise off the top of the wake and stay in the air longer, and many riders find it makes edging into the wake feel more stable.
Towers also:
- Get the rope above passengers’ heads
- Hold board racks, freeing up floor space
- Provide mounting points for speakers and lights
- Support a bimini or shade top on many designs
Skiers usually still use a low pylon, because slalom skiing benefits from a lower, more direct pull.
OEM vs aftermarket towers
Nearly every new wake boat offers a factory (OEM) tower, often with power folding and integrated lights and speakers. If you’re buying new, that’s usually the simplest route: it’s engineered for that hull, mounted in reinforced spots and covered by the boat’s warranty.
Aftermarket towers are for boats that didn’t come with one, like older inboards, runabouts and some deck boats, or for owners replacing a damaged tower.
Types of aftermarket towers
Boat-specific, universal and custom
- Boat-specific towers are made to fit a particular make and model. When one exists for your boat, it’s typically the easiest install and the cleanest look.
- Universal towers adjust to fit a range of beam widths and deck shapes. They’re widely available and generally cheaper, but fitting them takes more care. Mounting feet need to sit flat on curved or angled surfaces.
- Custom towers are fabricated to your boat’s measurements and your choices of finish and shape. They cost the most and take the longest.
Fixed vs folding
- Fixed towers are rigid and generally simpler and sturdier for the money. The catch is height: if your garage door, boat lift canopy or storage building has limited clearance, a fixed tower may not fit.
- Folding (collapsible) towers fold forward or backward for storage and trailering. Manual versions use pins or quick-release latches; higher-end factory towers fold with power. Check how low a folding tower actually goes. Some fold flat, others only to roughly windshield height.
Also measure total height with the tower up, so you know whether it clears bridges and covered storage on your usual route.
Will an aftermarket tower fit your boat?
Before buying, measure and confirm:
- Beam width at the mounting points. Universal towers list a supported range, and your boat needs to fall inside it.
- Mounting surfaces. Feet need a solid, reasonably flat place to sit on the gunwale or deck. Curved decks may need special pads or brackets.
- Deck strength. A tower under load puts real force into the deck. Many installers add backing plates under the mounting points to spread the load.
- Windshield and seating clearance. The front legs shouldn’t block walkways or the windshield’s opening.
- Storage height, fixed or folded.
Installation: DIY or professional?
Installing a tower means drilling through your deck, bedding fittings with marine sealant, and getting everything square and tight. Kits generally include brackets and hardware, and a mechanically handy owner with a helper can do it. But mistakes are hard to undo: a misplaced hole, a poorly sealed fitting that lets water into the core, or mounting into a weak spot.
If you aren’t confident, a marine shop or the tower’s dealer is a sensible choice. Either way, follow the tower maker’s instructions closely, and check fasteners after the first few outings, since things can settle.
Using a tower safely
- Tow only what the tower is rated for. Towers are designed for the pull of a single wakeboarder. Many manufacturers specifically warn against pulling tubes, kneeboards or multiple riders from the tower, because those loads can be much higher and come from sharp side angles. Use the boat’s ski eye or pylon for tubing.
- Inspect mounts regularly for cracks, loose bolts or fatigue around the feet.
- Lock folding mechanisms fully before towing.
- Remove or secure accessories before trailering at highway speed, especially soft racks and biminis.
Tower accessories
Common add-ons include board racks (usually rotating clamp-on designs), a tower bimini, LED lights, a tower bag for ropes and vests, and a flag holder for the down-skier flag where it’s required. Most clamp onto the tower tube, so check your tower’s tube diameter before buying. Aftermarket clamps are sized for specific diameters.
Wakeboard tower speakers
What makes a speaker tower-ready
Tower speakers live in sun, spray and rain, and they have to be heard by someone 20 to 70 feet behind a loud engine. Look for:
- Marine rating. UV-resistant housings and grilles, corrosion-resistant hardware, and drivers that tolerate moisture.
- Enclosed “pod” or “can” housings designed to mount on a tube and aim backward.
- A published water and dust resistance rating from the manufacturer, if available. A higher rating is better for exposed tower mounts.
Most tower speakers are coaxial, with the tweeter mounted in the center of the woofer, which keeps them compact and simple. Larger high-end towers sometimes use separate tweeters.
Size, power and amplification
Common tower speaker sizes run from around 6.5 inches to 10 inches and up. Larger drivers generally move more air and carry better outdoors, but they’re heavier and need more amplifier power.
Pay attention to RMS (continuous) power handling, not peak figures, and match it to an amplifier. Most tower speakers need a separate marine amplifier. Running them off a head unit’s built-in amp usually sounds weak once the engine is running.
Mounting and wiring
- Use clamps sized to your tower tubing.
- Run wiring through the tower tubes where possible, or route it neatly along the legs. Loose wires chafe and corrode.
- Use tinned marine-grade wire and sealed connections. Bare copper corrodes quickly near water.
- Mount speakers so they can swivel. Many owners aim them at the rider while riding and back toward the cockpit at anchor.
- Check that speakers and lights still clear a folded tower’s travel path.
Battery and charging
A powerful amplifier draws a lot of current, and playing music at anchor with the engine off can drain a starting battery. Many owners add a second battery with a battery switch or isolator, so the audio system can never leave them unable to start the engine. If you’re adding substantial amplifier power, have someone check that your wiring, fusing and charging system can handle it.
Keeping the noise neighborly
Tower speakers carry a long way over water. Sound that’s pleasant for the rider can be a real irritant to shoreline homes and anglers, and some lakes have noise ordinances. Turn it down near shore, in coves, at anchor near others, and early or late in the day. It’s also one of the easier ways to reduce friction between wake boaters and other lake users. See the debate over wake boats on lakes.
Care and maintenance
- Rinse towers and speakers with freshwater, especially after saltwater use.
- Check clamp bolts and mounting hardware for loosening and corrosion.
- Inspect wiring at the speakers and where it enters the tower.
- Cover speakers or remove them for winter storage, if practical.
- Listen for rattles. A buzzing speaker is often just a loose clamp.
For how the tower fits into the rest of the boat’s wake-making hardware, see the parts of a wakeboard boat.