Wake Boat Basics

What are the main parts of a sailing boat?

The main parts of a sailing boat explained: hull, keel, rudder, mast, boom, sails, rigging and deck hardware, plus port and starboard and how sailboats compare to wake boats.

On this page
  1. The hull and what’s attached below it
  2. The rig: mast, boom and sails
  3. Standing rigging vs running rigging
  4. Deck hardware
  5. Directions and sides
  6. How a sailboat’s parts compare with a wake boat’s

The main parts of a sailing boat are the hull (the boat’s body), the keel or centerboard (the fin underneath that keeps it from sliding sideways), the rudder with a tiller or wheel (for steering), the mast (the tall vertical spar), the boom (the horizontal spar along the bottom of the mainsail), the sails (usually a mainsail and a jib), and the rigging: the wires and ropes that hold the mast up and control the sails. Here’s what each one does.

The hull and what’s attached below it

Hull

The hull is the shell of the boat. It provides buoyancy and contains everything else: the cockpit, the cabin on larger boats, and storage. Its top edge is the gunwale (pronounced “gunnel”). The flat or angled surface across the back is the transom. The surface you walk on is the deck.

Keel, centerboard or daggerboard

Wind pushing on the sails tries to shove the boat sideways as well as forward. The keel, a fin that projects down from the bottom of the hull, resists that sideways slip so the boat can move forward and even sail at an angle toward the wind. On most cruising sailboats the keel is weighted (often with lead or iron), which also keeps the boat upright.

Small sailboats and dinghies often use a centerboard (which pivots up and down) or a daggerboard (which slides straight up and down) instead of a fixed keel. Both can be raised for shallow water or beaching.

Rudder and tiller or wheel

The rudder is a vertical blade at the back of the boat that steers by changing the direction water flows past it. Smaller boats steer with a tiller, a lever attached directly to the rudder. Larger boats usually have a wheel connected to the rudder through cables or hydraulics.

The rig: mast, boom and sails

  • Mast: the tall vertical pole that holds the sails up.
  • Boom: the horizontal pole attached low on the mast that holds the bottom edge of the mainsail. It swings across the boat when changing direction, so mind your head.
  • Mainsail: the large sail behind the mast, attached to both the mast and the boom.
  • Jib or genoa: the triangular sail in front of the mast. A genoa is a larger headsail that overlaps the mast.
  • Spinnaker: a large, lightweight, balloon-shaped sail used when sailing downwind. Not every boat has one.

A sail’s edges and corners have names too. The front edge is the luff, the back edge is the leech, the bottom edge is the foot, and the top corner is the head.

Standing rigging vs running rigging

Sailors divide the wires and ropes into two groups:

Standing rigging stays fixed and holds the mast up:

  • Forestay: runs from the top (or near the top) of the mast to the bow
  • Backstay: runs from the masthead to the stern
  • Shrouds: run from the mast to the sides of the boat

Running rigging moves and controls the sails:

  • Halyards: raise and lower sails
  • Sheets: control the angle of the sails to the wind (the mainsheet for the mainsail, jib sheets for the jib)
  • Boom vang, outhaul and traveler: fine-tune the mainsail’s shape and position
  • Reefing lines: reduce sail area in strong wind

Deck hardware

  • Winches: drums that give mechanical advantage when pulling in sheets and halyards
  • Cleats: fittings for securing lines
  • Blocks: pulleys that guide lines
  • Lifelines and stanchions: the wire “fence” and its posts around the deck on many cruising boats

Directions and sides

These terms apply to every kind of boat, sail or power:

  • Bow: the front
  • Stern: the back
  • Port: the left side when you’re facing the bow
  • Starboard: the right side when you’re facing the bow
  • Amidships: the middle

How do you remember port and starboard? Two common tricks:

  • “Port” and “left” both have four letters.
  • “There’s no red port left.” Port wine is red, and the port navigation light is red. Starboard’s light is green.

How a sailboat’s parts compare with a wake boat’s

Sailboats and powerboats share the basics: hull, deck, bow, stern, transom, gunwale, rudder, port and starboard. The differences are in propulsion and purpose:

Sailboat Wake boat
Propulsion Sails (often with an auxiliary engine) Inboard engine and propeller
Keeping it stable Weighted keel or centerboard Hull shape, tracking fins
Adding weight Keel ballast is permanent Water ballast pumped in and out
Tall structure Mast Tower for the tow rope
Key controls Sheets and halyards Throttle, ballast, surf system, speed control

For a full walkthrough of a towboat’s anatomy, see the parts of a wakeboard boat, or learn how its weight works in wake boat ballast and weight.

The complete guide to wake boat basics

How Wake Boats Work
Read the guide

Keep exploring

Guides from other topics

All topics →